Interior
Showing 1–20 of 24 results

SWITCH 12MM DPST 15A
Switch two terminals SPST (single-pole, single-throw) 12mm mounting 15a rated Commonly used with fuel pump relays, light relays, accessory power relays, or any other device drawing less than 15 amps.

MCP HALF INSERT – 2x 12MM (3D PRINTED)
This panel is designed and made to be used with our Modular Center Panel line. Full-size insert 2x 12mm mounting holes for switches, LEDs, etc. (not included) Material: 3D Printed in your material of choice. Made in Colorado, USA from … Continued

MCP FULL INSERT – 52MM GAUGE (3D PRINTED)
This panel is designed and made to be used with our Modular Center Panel line. Full-insert 52mm mounting hole for a 52mm gauge (gauge not included) Material: 3D Printed in your material of choice. What’s Included: 1x panel 4x M3 … Continued

E30 MODULAR CENTER PANEL
Customize it to your exact needs! Completely modular and customizable. All mounting positions have both full and half mounting available. Place any panel in any position. See available inserts in the Modular Center Panel category! Material: Brushed Aluminum Made in … Continued

E30 MODULAR CENTER VENT PODS
Replacing the center HVAC vents with customizable, modular pods has never been easier. Choose from hundreds of different setups to match exactly what you need. Simple to install, easy to read, and massively configurable. Choose from premade pod inserts (panels), … Continued

CEPHALO-POD MOUNT – TRIPLE 52MM
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD MOUNT – 60MM GAUGE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD MOUNT – 45MM GAUGE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD MOUNT – 52MM GAUGE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD BASE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CONNECTOR 3.5MM HEADPHONE JACK 6MM
Connector three terminals 3.5mm standard headphone jack, commonly used with audio and voice connections 6mm mounting

BUTTON 10MM MOMENTARY
Momentary Button Two terminals Momentary button (connection only shorted while depressed) 10mm mounting Red cap 12 amp rated

BUTTON 6MM MOMENTARY
Momentary Button Two terminals Momentary button (connection only shorted while depressed) 6mm mounting Black or blue caps available 5 amp rated

LED 6MM 5-20V
LED Rated for use with 5-20 volt sources. No resistors or voltage regulators needed! Many colors to choose from Pre-wired pigtail 6mm mounting

SWITCH 20MM LED SPST 10A
Switch three terminals (5-16v source, LED ground, and source dump) SPST (single-pole, single-throw; ON/OFF) 20mm mounting 10a rated

SWITCH 6MM DPST 6A
Switch three terminals (pos. 1 – common – pos. 2) DPST (double-pole, single-throw) 6mm mounting 6a rated (good for most relays, lights, and similar components drawing less than 6 amps)

MCP HALF INSERT – 3x 10MM (3D PRINTED)
This panel is designed and made to be used with our Modular Center Panel line. Full-size insert 3x 10mm mounting holes for switches, LEDs, etc. (not included) Material: 3D Printed in your material of choice. What’s Included: 1x panel 4x … Continued

MCP HALF INSERT – 2x 10MM (3D PRINTED)
This panel is designed and made to be used with our Modular Center Panel line. Full-size insert 2x 10mm mounting holes for switches, LEDs, etc. (not included) Material: 3D Printed in your material of choice. What’s Included: 1x panel 4x … Continued

MCP FULL INSERT – OE BUTTONS (ALUMINUM)
This panel is designed and made to be used with our Modular Center Panel line. Full-insert 3x mounts for OE BMW buttons, such as from E24, E28, E30, E34, E36, and many others. Please use common sense with compatibility! (buttons … Continued

MCP FULL INSERT – 52MM GAUGE (ALUMINUM)
This panel is designed and made to be used with our Modular Center Panel line. Full-insert 52mm mounting hole for a 52mm gauge (gauge not included) Material: Brushed Aluminum Made in Colorado, USA from start to finish! Support multiple small, … Continued