SSSQUID
Showing 101–120 of 148 results
Shipped and sold directly by SSSQUID!

SSSMCK MODULE: VARIABLE TPS (ALPHA-N)
This module contains all the necessary hardware and connections to convert your M20 or M30 to a variable TPS (or Alpha-N) tuning. This kit REQUIRES a specific tune to work properly. This module uses the two extra configurable outputs to … Continued

VAM CALIBRATION
VAM (Volume Airflow Meter) calibration is the process of making manual adjustments to the inner components of a VAM in order to correctly match its signal output to the airflow throughput. There are a few reasons why a VAM may … Continued

E30 ABS DELETE KIT
At this point we have discontinued production of this kit for the foreseeable future. This may change, but at this point we are beyond production capacity and they take too long and cost too much to produce. Easily delete ABS … Continued

SQUID INK: GEARBOX
SQUID INK: GEARBOX is a revolutionary transmission oil additive designed to significantly decrease gearbox (transmission / differential) component wear. After extensively testing, we introduce this additive specifically for transmissions and differentials. This additive lowers operating temperature, increases wear resistance, and … Continued

M30 VAM (AFM) INLET ADAPTER
Available in many sizes! Works with the M30B32/34/35 VAM (AFM)! Can mount the stock intake box to an intake track or metering device (such as MAF), or it can be mounted to the stock VAM to be used with an … Continued

CEPHALO-POD MOUNT – TRIPLE 52MM
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD MOUNT – 60MM GAUGE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD MOUNT – 45MM GAUGE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD MOUNT – 52MM GAUGE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CEPHALO-POD BASE
The Cephalo-Pod is an articulated and customizable gauge pod system. With thousands of mounting combinations and a wide variety of mountable devices, there’s sure to be something to match your needs. And if you don’t see it, we can make … Continued

CONNECTOR 3.5MM HEADPHONE JACK 6MM
Connector three terminals 3.5mm standard headphone jack, commonly used with audio and voice connections 6mm mounting

BUTTON 10MM MOMENTARY
Momentary Button Two terminals Momentary button (connection only shorted while depressed) 10mm mounting Red cap 12 amp rated

BUTTON 6MM MOMENTARY
Momentary Button Two terminals Momentary button (connection only shorted while depressed) 6mm mounting Black or blue caps available 5 amp rated

LED 6MM 5-20V
LED Rated for use with 5-20 volt sources. No resistors or voltage regulators needed! Many colors to choose from Pre-wired pigtail 6mm mounting

SWITCH 20MM LED SPST 10A
Switch three terminals (5-16v source, LED ground, and source dump) SPST (single-pole, single-throw; ON/OFF) 20mm mounting 10a rated

SWITCH 6MM DPST 6A
Switch three terminals (pos. 1 – common – pos. 2) DPST (double-pole, single-throw) 6mm mounting 6a rated (good for most relays, lights, and similar components drawing less than 6 amps)

MCP HALF INSERT – 3x 10MM (3D PRINTED)
This panel is designed and made to be used with our Modular Center Panel line. Full-size insert 3x 10mm mounting holes for switches, LEDs, etc. (not included) Material: 3D Printed in your material of choice. What’s Included: 1x panel 4x … Continued

MCP HALF INSERT – 2x 10MM (3D PRINTED)
This panel is designed and made to be used with our Modular Center Panel line. Full-size insert 2x 10mm mounting holes for switches, LEDs, etc. (not included) Material: 3D Printed in your material of choice. What’s Included: 1x panel 4x … Continued

MCP FULL INSERT – OE BUTTONS (ALUMINUM)
This panel is designed and made to be used with our Modular Center Panel line. Full-insert 3x mounts for OE BMW buttons, such as from E24, E28, E30, E34, E36, and many others. Please use common sense with compatibility! (buttons … Continued

MCP FULL INSERT – 52MM GAUGE (ALUMINUM)
This panel is designed and made to be used with our Modular Center Panel line. Full-insert 52mm mounting hole for a 52mm gauge (gauge not included) Material: Brushed Aluminum Made in Colorado, USA from start to finish! Support multiple small, … Continued
David Sellars (verified buyer) –